Daily maintenance me身廠asures required for sand 林吃blasting room system

The machine equipment in the s他微andblasting room consi費著sts of sandblas玩很ting room body, sand 見腦shot recycling system software, aut內快omatic sandblastin知門g machine, organic 民志waste gas treatment system 離購software, lighting system softwa站了re, and electrical equipment au腦河tomatic control system. The syste鄉玩m software is separated from th照現e sand shot removal cycle.男習 Some of the design sc刀音hemes are the same. The key point of 都綠this paper is to co房樂mpare the form of the sand sho我大t recycling system software and the r市區outine maintenance countermeasures tha月很t must be carried out for t了和he sand blasting room syst書個em software.

The sand blasting room recyc年現ling system softwar人上e is a closed recycling system s亮體oftware that the sand shot sprayed by可錯 the sand blasting gun is recy黑習cled back to the sand blasti問愛ng treatment cyl舞兒inder. The dust shot in the sand bl動都asting room is collected, and th報男en the dust shot is raised to the dust但南 shot separation equipment to separ林術ate the dust shot. The effective shot司月 after separation is automatically exp就信loded into the shot 路是storage box, and the sand shot年費 in the shot sto拍愛rage box is automatic知南ally fed into the sand cyl通綠inder according to 畫空the command, Subsequentl木器y, the sandblasting gun is provided f好街or sandblasting again. This cycle i長這s the sand shot recycling sys海去tem software.

Start the natural ventilation科放 dedusting motor first, check the op機腦eration condition, a商中nd restart the shot blasting ma妹男chine after confirming that eve懂愛rything is normal. Befor土哥e the shot blasting machine is s快內tarted, do not open the contr醫喝ol gate valve for iron服機 shot supply. To frequently check 山海the removal quality of sta黃冷inless steel plate能弟s, if necessary, the shot wheel請東 shooting angle and the roller t男下ransport speed can be a東大djusted. Check whether th章風e stainless steel plate has directi黃工onal deviation at any time and any鐘費where, and remove the deviation爸腦 immediately. Pa慢得y attention to whether the vibrati去暗on of the shot blastin信兒g machine and the sound box are norma媽少l during operation花動, and the temperature rise of the roll中用ing bearing and motor問外. In case of any abnormality, stop 大黑the machine for inspection, fault det吧會ection or leaf replacement. When the wo計見rk of the shot blasting and rust r內呢emoval room is completed裡道, the shot tube shall be shut down firs道站t and the air supply著計 shall be termina拿美ted; Turn off the shot bl計吧asting motor and finally stop the exha動愛ust fan. In case of any abnormal如和ity, shut down the m舞劇achine immediately大錢, check the cause and 他那remove it immediat業章ely. It is forbidden to enter the sho和業t blasting room for shot blasting of w不業et cold thick s鐘小teel plates.

The circulating recovery system s日相oftware of sand blasting r她化oom is currently多間 sold in the mar章和ket in two ways: pe樹微dal circulation recovery and force 吧靜circulation recovery. To put it bluntl好笑y, energy recovery means that on the w市農ood floor of the sandblasti唱讀ng room, the design scheme has several 得懂small cone buckets, and a hole 什嗎is opened at the bottom of the南下 cone bucket. This hole is based on th票議e outdoor cyclone dust remove為匠r caused by the ventilation章做 duct. A high press亮分ure centrifugal fan is selected 厭煙to extract the dust pell又女ets falling in the cone 兒知bucket at the bottom of the room.廠事 After the separation of the cyclone在唱 dust remover, the effective sand p人會ellets fall into the路都 shot storage bo東綠x in the middle of the sepa書南ration equipment, Then enter頻鐵 the sand tank to complete書少 the circulatio土河n.